preliminarysubject to change without notice order number: MPC7410PDPNS/d rev. 0, 7/2001 semiconductor products sector this document contains information on a new product under development by motorola. motorola reserves the right to change or discontinue this product without notice. ? motorola, inc., 2001. all rights reserved. motorola part numbers affected: xpc7410rx450pd xpc7410rx500pd xpc7410rx533pd mpc7410 part number speci?cation for the rx xxx pd series this document describes part-number-speci?c changes to recommended operating conditions and revised electrical speci?cations, as applicable, from those described in the general mpc7410 hardware speci?cations (order #: mpc7410ec/d). speci?cations provided in this document supersede those in the mpc7410 hardware speci?cations , rev. 0.3 (dated 3/2001) for the part numbers listed in table a only. speci?cations not addressed herein are unchanged. because this document is frequently updated, refer to http://www.motorola.com/sps or to your motorola sales of?ce for the latest version. note that headings and table numbers in this document are not consecutively numbered. they are intended to correspond to the heading or table affected in the general hardware speci?cation. part numbers addressed in this document are listed in table a. for more detailed ordering information see table b.
2 mpc7410 part number speci?cation for the rxxxxpd series errata errata this section summarizes design defects or errors (errata) that are known to exist for these parts. there may be additional errata that are not known or are not yet documented here which may cause the part to deviate from the functional description provided in the mpc7410 risc microprocessor users manual (order # mpc7410um/ad rev 0). contact your local motorola sales of?ce for later and/or more detailed description of the errata. the known errata as of the date of this document are summarized below. table a. part numbers addressed by this data sheet motorola part number operating conditions signi?cant differences from hardware speci?cation cpu frequency vdd t j (c) xpc7410rx450pd 450 mhz 2.0v50mv 0 to 65 modi?ed voltage & temperature speci?cation to achieve 450mhz frequency xpc7410rx500pd 500 mhz 2.0v50mv 0 to 65 modi?ed voltage & temperature speci?cation to achieve 500mhz frequency xpc7410rx533pd 533 mhz 2.0v50mv 0 to 65 modi?ed voltage & temperature speci?cation to achieve 533mhz frequency note: the x pre?x in a motorola powerpc part number designates a pilot production prototype as de?ned by motorola sop 3-13. these are from a limited production volume of prototypes manufactured, tested and q.a. inspected on a quali?ed technology to simulate normal production. these parts have only preliminary reliability and characterization data. before pilot production prototypes may be shipped, written authorization from the customer must be on ?le in the applicable sales of?ce acknowledging the quali?cation status and the fact that product changes may still occur while shipping pilot production prototypes. # problem description impact work-around 1 timebase or decrementer may lose accuracy in nap mode. the timebase counter or decrementer may lose accuracy when transitioning from the nap power saving mode. any system which uses the nap power saving mode and requires absolute accuracy from the timebase counter or decrementer. do one of the following: 1. avoid the use of nap mode. 2. avoid using the timebase counter or decrementer for highly accurate measurements. 2 iftt mode does not identify dcbt/dst instructions as data fetches. the instruction fetch transaction type (iftt) encoding differentiation mode does not correctly identify dcbt/dst instructions as data fetches. any system which depends on iftt to differentiate instruction from data fetches. do the following: 1. replace dcbt/dst with dcbtst/dstst. 2. set hid0[nopti] and hid0[nopdst] to no-op all touch instructions. 3. remove dcbt/dst from the code. 3 tau reports incorrect temperatures. the thermal assist unit (tau) reports temperatures between 35 to 55 degrees lower than actual. programmed trip temperatures will not trigger output interrupts even if actual temperatures exceed the setpoint by up to 55 degrees. none.
mpc7410 part number speci?cation for the rxxxxpd series 3 preliminarysubject to change without notice features 1.2 features this section summarizes changes to the features of the mpc7410 described in the mpc7410 hardware speci?cations. none. 1.4.1 dc electrical characteristics table 3 provides the recommended operating conditions for the mpc7410 part numbers described herein. table 7 provides the power consumption for the mpc7410 part at the frequencies described herein. table 3. recommended operating conditions characteristic symbol recommended value unit core supply voltage vdd 2.0v 50mv v pll supply voltage avdd 2.0v 5 0mv v l2 dll supply voltage l2avdd 2.0v 50mv v processor bus supply voltage bvsel = hreset ovdd 2.5v 125mv v bvsel = gnd ovdd 1.8v 90mv v l2 bus supply voltage l2vsel = hreset l2ovdd 2.5v 125mv v l2vsel = gnd l2ovdd 1.8v 90mv v input voltage processor bus v in gnd to ovdd v l2 bus v in gnd to l2ovdd v jtag signals v in gnd to ovdd v die-junction temperature t j 0-65 c note: these are the recommended and tested operating conditions. proper device operation outside of these conditions is not guaranteed. table 7. power consumption for mpc7410 processor (cpu) frequency processor (cpu) frequency processor (cpu) frequency unit notes 450mhz 500mhz 533mhz full-on mode typical maximum 5.9 6.5 6.9 w 1, 3 13.2 14.7 15.6 w 1, 2 doze mode maximum 4.5 5 5.3 w 1, 2 nap mode
4 mpc7410 part number speci?cation for the rxxxxpd series dc electrical characteristics 1.4.2.1 clock ac speci?cations table 8 provides the additional clock ac timing speci?cations described in this document. refer to the mpc7410 hardware speci?cation for the remaining frequencies . maximum 2.13 2.25 2.33 w 1, 2 sleep mode maximum 2.13 2.25 2.33 w 1, 2 sleep modepll and dll disabled typical 0.5 0.5 0.5 w 1, 3 maximum 2.0 2.0 2.0 w 1, 2 notes: 1. these values apply for all valid processor bus and l2 bus ratios. the values do not include i/o supply power (ovdd and l2ovdd) or pll/dll supply power (avdd and l2avdd). ovdd and l2ovdd power is system dependent, but is typically <10% of vdd power. worst case power consumption for avdd = 15 mw and l2avdd = 15 mw. 2. maximum power is measured at 65 c and vdd = 2.05v while running an entirely cache-resident, contrived sequence of instructions which keep the execution units, including altivec, maximally busy. 3. typical power is an average value measured at 65 c and vdd = 2.0v in a system while running typical benchmarks. table 8. clock ac timing specifications at recommended operating conditions (see table 3) characteristic symbol 450 mhz 500 mhz 533 mhz unit notes min max min max min max processor frequency f core 300 450 300 500 300 533 mhz vco frequency f vco 600 900 600 1000 600 1066 mhz sysclk frequency f sysclk 33 133 33 133 33 133 mhz 1 sysclk cycle time t sysclk 7.5 30 7.5 30 7.5 30 ns sysclk rise and fall time t kr 1.0 1.0 1.0 ns 2 t kf 0.5 0.5 0.5 ns 3 sysclk duty cycle measured at ovdd/2 t khkl /t sys clk 40 60 40 60 40 60 % 4 sysclk jitter 150 150 150 ps 5 internal pll relock time 100 100 100 s6 notes: see general hardware speci?cation. table 7. power consumption for mpc7410 (continued) processor (cpu) frequency processor (cpu) frequency processor (cpu) frequency unit notes 450mhz 500mhz 533mhz
mpc7410 part number speci?cation for the rxxxxpd series 5 preliminarysubject to change without notice dc electrical characteristics 1.4.2.2 processor bus ac speci?cations table 9 provides the processor bus ac timing speci?cations for the mpc7410 part described in this document . table 9. processor bus ac timing specifications 1 at vdd=avdd=2.0v50mv; 0 tj 65c, ovdd = 2.5v0.125v and ovdd = 1.8v0.090v, 60x bus at 133mhz parameter symbol 450, 500, 533 mhz unit notes min max mode select input setup to hreset t mvrh 8t sysclk 2,3,4,5 hreset to mode select input hold t mxrh 0 ns 2,3,5 setup times: address/transfer attribute transfer start (ts ) data/data parity ar tr y /shd0 /shd1 all other inputs t avkh t tsvkh t dvkh t arvkh t ivkh 1.4 1.4 1.4 1.4 1.4 ns10 6 7 8 input hold times: address/transfer attribute transfer start (ts ) data/data parity ar tr y /shd0 /shd1 all other inputs t axkh t tsxkh t dxkh t arxkh t ixkh 0 0 0 0 0 ns11 6 7 8 valid times: address/transfer attribute ts , abb , dbb data data parity ar tr y /shd0 /shd1 all other outputs t khav t khtsv t khdv t khdpv t kharv t khov 3.0 3.0 3.5 3.5 2.3 3.0 ns12 6 7 7 9 output hold times: address/transfer attribute ts , abb , dbb data/data parity ar tr y /shd0 /shd1 all other outputs t khax t khtsx t khdx t kharx t khox 0.75 0.75 0.6 0.75 0.75 ns13 6 7 9 sysclk to output enable t khoe 0.5 ns 14 sysclk to output high impedance (all except ts , abb/amon(0) , ar tr y /shd , dbb/dmon(0) t khoz 3.5 ns 15
6 mpc7410 part number speci?cation for the rxxxxpd series dc electrical characteristics 1.4.2.3 l2 clock ac speci?cations table 10 provides the l2clk output ac timing speci?cations for the mpc7410 part described in this document. sysclk to ts , abb/amon(0) , dbb/dmon(0) high impedance after precharge t khabpz 1.0 t sysclk 4,15, 16,17 maximum delay to ar tr y /shd0 /shd1 precharge t kharp 1t sysclk 4,17 sysclk to ar tr y /shd0 /shd1 high impedance after precharge t kharpz 2t sysclk 4,17 notes: see general hardware speci?cation. table 10. l2clk output ac timing specifications at recommended operating conditions (see table 3) parameter symbol 450 mhz 500 mhz 533 mhz unit notes min max min max min max l2clk frequency f l2clk 150 225 150 250 150 266 mhz 1 l2clk cycle time t l2clk 4.4 6.67 4.0 6.67 3.76 6.67 ns l2clk duty cycle t chcl /t l2 clk 50 50 50 % 2 internal dll-relock time 640 640 640 l2clk 4 dll capture window 200 200 200 ns 5 notes: see general hardware speci?cation. table 9. processor bus ac timing specifications 1 (continued) at vdd=avdd=2.0v50mv; 0 tj 65c, ovdd = 2.5v0.125v and ovdd = 1.8v0.090v, 60x bus at 133mhz parameter symbol 450, 500, 533 mhz unit notes min max
mpc7410 part number speci?cation for the rxxxxpd series 7 preliminarysubject to change without notice ordering information 1.4.2.4 l2 bus ac speci?cations table 11 provides the l2 bus interface ac timing speci?cations for the frequencies described in this document. 1.10 ordering information table b provides the ordering information for the mpc7410 part described in this document. table 11. l2 bus interface ac timing specifications at vdd=avdd=l2avdd= 2.05v50mv; 0 tj 65c, l2ovdd = 2.5v0.125v and l2ovdd =1.8v0.090v parameter symbol 450 mhz 500 mhz 533 mhz unit notes min max min max min max l2sync_in rise and fall time t l2cr & t l2cf 1.0 1.0 1.0 ns 1 setup times: data and parity t dvl2ch 1.375 1.250 1.168 ns2 input hold times: data and parity t dxl2ch 0.0 0.0 0.0 ns2 valid times: all outputs when l2cr[14-15] = 00 all outputs when l2cr[14-15] = 01 all outputs when l2cr[14-15] = 10 all outputs when l2cr[14-15] = 11 t l2chov - - - - 2.375 tbd tbd tbd - - - - 2.25 tbd tbd tbd - - - - 2.17 tbd tbd tbd ns 3,4 output hold times all outputs when l2cr[14-15] = 00 all outputs when l2cr[14-15] = 01 all outputs when l2cr[14-15] = 10 all outputs when l2cr[14-15] = 11 t l2chox 0.55 tbd tbd tbd - - - - 0.5 tbd tbd tbd - - - - 0.47 tbd tbd tbd - - - - ns3 l2sync_in to high impedance: all outputs when l2cr[14-15] = 00 all outputs when l2cr[14-15] = 01 all outputs when l2cr[14-15] = 10 all outputs when l2cr[14-15] = 11 t l2choz - - - - 2.0 2.5 3.0 3.5 - - - - 2.0 2.5 3.0 3.5 - - - - 2.0 2.5 3.0 3.5 ns notes: see general hardware speci?cation table b. ordering information for the mpc7410 microprocessor package type device rev process mask code cpu frequency (mhz) motorola part number 360 cbga 1.3 hip 6 83k65d 450mhz xpc7410rx450pd 500mhz xpc7410rx500pd 533mhz xpc7410rx533pd
information in this document is provided solely to enable system and software implementers to use powerpc microprocessors. ther e are no express or implied copyright licenses granted hereunder to design or fabricate powerpc integrated circuits or integrated circuits based on the information in this document. motorola reserves the right to make changes without further notice to any products herein. motorola makes no warranty, represen tation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. typical parameters which may be provided in motorola data sheets and/or specifications can and do vary in different applications and actual perfor mance may vary over time. all operating parameters, including typicals must be validated for each customer application by customers technical ex perts. motorola does not convey any license under its patent rights nor the rights of others. motorola products are not designed, intended, or autho rized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, o r for any other application in which the failure of the motorola product could create a situation where personal injury or death may occur. should buyer pu rchase or use motorola products for any such unintended or unauthorized application, buyer shall indemnify and hold motorola and its officers, employe es, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising ou t of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that moto rola was negligent regarding the design or manufacture of the part. motorola and are registered trademarks of motorola, inc. motorola, inc. is an equal opportunity/affirmative action employer. how to reach us: usa/europe/locations not listed: motorola literature distribution; p.o. box 5405, denver, colorado 80217. 1-303-675-2140 or 1-800-441-2447 japan: motorola japan ltd.; sps, technical information center, 3-20-1, minami-azabu. minato-ku, tokyo 106-8573 japan. 81-3-3440 -3569 asia/pacific: motorola semiconductors h.k. ltd.; silicon harbour centre, 2 dai king street, tai po industrial estate, tai po, n .t., hong kong. 852-26668334 technical information center: 1-800-521-6274 home page: http://www.motorola.com/semiconductors document comments: fax (512) 933-2625, attn: risc applications engineering world wide web addresses : http://www.motorola.com/powerpc http://www.motorola.com/netcomm http://www.motorola.com/coldfire MPC7410PDPNS/d digitaldna is a trademark of motorola, inc. the powerpc name, the powerpc logotype, and powerpc 603e are trademarks of international business machines corporation used by motorola under license from international business machines corporation. 1.10.1 part marking parts are marked as the example shown in figure a. figure a. motorola part marking for bga device bga notes : ccccc is the country of assembly (this space is left blank if parts are assembled in the united states) mmmmmm is the 6-digit mask number atwlyywwa is the traceability code xpc7410 rx450pd mmmmmm atwlyywwa 7410
|
